DualPart® Coco
Uniquely amongst leading brands, T.A. DualPart® Coco doesn’t need additives for success from seed to bloom : other coco specific 2-part nutrients require additional Cal/Mag and PK boosters, as well as 2 bottles of "grow" and 2 bottles of "Bloom" nutrients. Not so with DualPart® Coco: two bottles are all you need!
DualPart® Coco is exceptionally rich in calcium and magnesium, but it also contains the full range of other elements that a plant needs for healthy vigorous growth, followed by bountiful flowering and fruiting. This includes the trace microelements which give your final product all the aroma and flavour that your plant is capable of developing.
As with most of our nutrients you use both DualPart® Coco Grow and Bloom throughout the lifecycle of your plants; you simply change the ratio between the two as your plants progress: there is no second set of bottles to buy when you go from grow to bloom.
This nutrient is produced according to one formula – however for this product, values are declared in chemical elements in South Africa/Australia and in oxides in Europe; which leads to differences in labels.
How to use:
- Shake well before each use, add each part to water separately, mix thoroughly, and always rinse measuring equipment.
- For best results, use DualPart® Coco with super clean T.A. Coco Fiber, Coco Fiber with Perlite coco coir .
- T.A. DualPart® Coco is very concentrated : a maximum of just 4.5 ml/L in water is required. See the main T.A. DualPart® Coco feed chart below.
FinalPart®
The industry standard way to end a grow - FinalPart® is our best-selling product for a good reason!
Final Part® is a complete late flowering nutrient/stimulant requiring no additional boosters. It increases flowering and production of active principles, and eliminates nutrient excess.
FinalPart® acts in 3 ways :
- It sends the plant a strong signal that it is coming to the end of its life; this prompts the plant to accelerate the ripening process.
- It forces the plant to strengthen its defences and thus increase essential oil and active principle production.
- It delivers all the mineral salts the plants need in a form that is easy to assimilate : in case of a previous accumulation of nitrate or microelements, this helps metabolize residues, which improves taste.
As a "forcing solution", FinalPart® can be used in any circumstance where you need to control or enhance ripening, and at the end of every flowering/fruiting cycle of annual flowers and fruits to maximise yield and flavour intensity.
Outdoors, FinalPart® enables you to quickly harvest a crop before it is spoiled by cold and damp weather. Indoors, it helps you harmonise the end of the grow cycle by speeding up the ripening of the slowest plants or varieties.
And in case of a severe infestation of fungi or insects, it can allow you to accelerate the natural cycle and recover something out of a crop that would otherwise be completely lost.
How to use:
- In hydroponics : replace old nutrient solution with pH adjusted water add up to 5 ml/L of FinalPart® to match or slightly exceed your previous EC (up to 2.6) and mix well. Run for 10 days, or as needed, then use FlashClean® to finish or harvest your crop directly.
- In soil : apply in pH adjusted water at up to 4 ml/L to match or slightly exceed your previous EC (up to 2.0). Apply until leaf yellowing occurs and/or ripening is satisfactory. This can take from 10 to 20 days. Then use FlashClean® to finish or harvest your crop directly.
- Expert growers can use FinalPart® to manipulate water stress to maximise active principal concentration, and minimise splitting in soft fruit culture : target EC 2.6 ms in hydro and target EC 2.0 ms in soil.
The set contains:
- 1x T.A. DualPart Coco Grow 500ml (FloraCoco)
- 1x T.A. DualPart Coco Bloom 500ml (FloraCoco)
- 1x T.A. Final Part 500ml (Ripen)
